C:\>cd data \DATA C:\DATA\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\DATA\ . 01-19-12 5:50a .. 01-19-12 5:50a 0 file(s) 0 bytes 2 dir(s) 246,071,296 bytes free C:\DATA\>cd .. C:\> Nortek Vec: DISABLED EPS Mapper: DISABLED MAVS: DISABLED OCR 504: *ENABLED* IMM: DISABLED Upload Auxilary Files: *ENABLED* OCR504 uart opened Configuration file settings: ---------------------------- Number of parameters to read: 8 First cycle set for: Sat Jan 19 00:00:00 2013 Clamp test delay set for: 1 minutes Cycle interval set for: 360 minutes Ascending timeout set for: 800 seconds Ascending trigger depth set for: 4.0 meters Descending timeout set for: 600 seconds Descending trigger depth set for: 50.0 meters Time to wait at surface set for: 0 seconds Stored calibration settings: ---------------------------- Motor current coefficient: 0.000755 Aux 1 current coefficient: 0.000220 Aux 2 current coefficient: 0.000220 Aux 3 current coefficient: 0.000220 Aux 4 current coefficient: 0.000219 Switched battery voltage coefficient: 0.004305 Switched aux voltage coefficient: 0.004290 Depth coefficient: 0.106744 Motor current offset: -15 Aux 1 current offset: 13 Aux 2 current offset: 32 Aux 3 current offset: 6 Aux 4 current offset: 21 Switched battery voltage offset: -34 Switched aux voltage offset: -1 Depth offset: 808 Directory 'DATA' found. SeaHorse II Ver. 2.091 Next cycle will start 5 seconds from now... Press the '&' key to bypass sampling and enter the main menu... Waiting... Nortek Vec: DISABLED EPS Mapper: DISABLED MAVS: DISABLED OCR 504: *ENABLED* IMM: DISABLED Upload Auxilary Files: *ENABLED* OCR504 uart opened Configuration file settings: ---------------------------- Number of parameters to read: 8 First cycle set for: Sat Jan 19 00:00:00 2013 Clamp test delay set for: 1 minutes Cycle interval set for: 360 minutes Ascending timeout set for: 800 seconds Ascending trigger depth set for: 4.0 meters Descending timeout set for: 600 seconds Descending trigger depth set for: 50.0 meters Time to wait at surface set for: 0 seconds Stored calibration settings: ---------------------------- Motor current coefficient: 0.000755 Aux 1 current coefficient: 0.000220 Aux 2 current coefficient: 0.000220 Aux 3 current coefficient: 0.000220 Aux 4 current coefficient: 0.000219 Switched battery voltage coefficient: 0.004305 Switched aux voltage coefficient: 0.004290 Depth coefficient: 0.106744 Motor current offset: -15 Aux 1 current offset: 13 Aux 2 current offset: 32 Aux 3 current offset: 6 Aux 4 current offset: 21 Switched battery voltage offset: -34 Switched aux voltage offset: -1 Depth offset: 808 Directory 'DATA' found. SeaHorse II Ver. 2.091 Next cycle will start 5 seconds from now... Press the '&' key to bypass sampling and enter the main menu... Waiting... SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? e Displaying system data Type 'q' to quit...any other key to continue Motor curnt(a/d): 102 Current: 0.088(a) Aux 1 curnt(a/d): 332 Current: 0.070(a) Aux 2 curnt(a/d): 25 Current: -0.002(a) Aux 3 curnt(a/d): 113 Current: 0.024(a) Aux 4 curnt(a/d): 23 Current: 0.000(a) Battery(a/d): 3157 Battery: 13.737(v) Aux(a/d): 3164 Aux: 13.578(v) Depth(a/d): 802 Depth: -0.640(m) Selector Status: 0 Motor curnt(a/d): 101 Current: 0.088(a) Aux 1 curnt(a/d): 337 Current: 0.071(a) Aux 2 curnt(a/d): 26 Current: -0.001(a) Aux 3 curnt(a/d): 145 Current: 0.031(a) Aux 4 curnt(a/d): 23 Current: 0.000(a) Battery(a/d): 3150 Battery: 13.707(v) Aux(a/d): 3157 Aux: 13.548(v) Depth(a/d): 797 Depth: -1.174(m) Selector Status: 0 Motor curnt(a/d): 100 Current: 0.087(a) Aux 1 curnt(a/d): 336 Current: 0.071(a) Aux 2 curnt(a/d): 26 Current: -0.001(a) Aux 3 curnt(a/d): 144 Current: 0.030(a) Aux 4 curnt(a/d): 22 Current: 0.000(a) Battery(a/d): 3150 Battery: 13.707(v) Aux(a/d): 3157 Aux: 13.548(v) Depth(a/d): 796 Depth: -1.281(m) Selector Status: 0 Motor curnt(a/d): 99 Current: 0.086(a) Aux 1 curnt(a/d): 334 Current: 0.071(a) Aux 2 curnt(a/d): 25 Current: -0.002(a) Aux 3 curnt(a/d): 145 Current: 0.031(a) Aux 4 curnt(a/d): 23 Current: 0.000(a) Battery(a/d): 3151 Battery: 13.711(v) Aux(a/d): 3158 Aux: 13.552(v) Depth(a/d): 802 Depth: -0.640(m) Selector Status: 0 SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? q ---------------------------------------------------------------- Persistor CF21M SN 04471 PicoDOS V4.01r1 PBM V4.00 (C) 1998-2005 Persistor Instruments Inc. - www.persistor.com ---------------------------------------------------------------- C:\>type header.txt ** Cruise: NBP12-01 ** Station: 1 ** Ship: RVIB Nathaniel B Palmer ** Chief_Scientist: Greenan ** Organization: DFO ** Area_of_Operation: Ross Sea ** Package: SeaHorse/SBE19plus CTD/WetStar/SBE43-DO/Satlantic OCR504i/FRRF ** Mooring_Number: 1 ** Latitude: -76 29.0 ** Longtitude: 171 06.0 ** Sounding: 800 ** Profile_Number: ** Profile_Direction: up ** Notes: C:\> C:\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\ OCR504.HDR 1,294 10-19-11 1:57p TESTFILE.001 0 01-20-12 11:36p DATA 01-19-12 5:50a CONFIG.TXT 192 01-19-12 2:19a OPFILE.TXT 13 01-19-12 2:20a HEADER.TXT 375 01-14-12 8:23p DATA2 10-25-11 1:28p 5 file(s) 1,874 bytes 2 dir(s) 246,071,296 bytes free C:\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\ OCR504.HDR 1,294 10-19-11 1:57p TESTFILE.001 0 01-20-12 11:36p DATA 01-19-12 5:50a CONFIG.TXT 192 01-19-12 2:19a OPFILE.TXT 13 01-19-12 2:20a HEADER.TXT 375 01-14-12 8:23p DATA2 10-25-11 1:28p 5 file(s) 1,874 bytes 2 dir(s) 246,071,296 bytes free C:\> Nortek Vec: DISABLED EPS Mapper: DISABLED MAVS: DISABLED OCR 504: *ENABLED* IMM: DISABLED Upload Auxilary Files: *ENABLED* OCR504 uart opened Configuration file settings: ---------------------------- Number of parameters to read: 8 First cycle set for: Sat Jan 19 00:00:00 2013 Clamp test delay set for: 1 minutes Cycle interval set for: 360 minutes Ascending timeout set for: 800 seconds Ascending trigger depth set for: 4.0 meters Descending timeout set for: 600 seconds Descending trigger depth set for: 50.0 meters Time to wait at surface set for: 0 seconds Stored calibration settings: ---------------------------- Motor current coefficient: 0.000755 Aux 1 current coefficient: 0.000220 Aux 2 current coefficient: 0.000220 Aux 3 current coefficient: 0.000220 Aux 4 current coefficient: 0.000219 Switched battery voltage coefficient: 0.004305 Switched aux voltage coefficient: 0.004290 Depth coefficient: 0.106744 Motor current offset: -15 Aux 1 current offset: 13 Aux 2 current offset: 32 Aux 3 current offset: 6 Aux 4 current offset: 21 Switched battery voltage offset: -34 Switched aux voltage offset: -1 Depth offset: 808 Directory 'DATA' found. SeaHorse II Ver. 2.091 Next cycle will start 5 seconds from now... Press the '&' key to bypass sampling and enter the main menu... Waiting... SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? f FREE MODE Cam_sw: 0 Current: 0.375 Apk SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? c CLIMB MODE Cam_sw: 1 Current: 0.331 Apk SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? g Entering user configuration setup Enter time (mm/dd/yyyy hh:mm:ss) of first cycle [01/21/2012 01:16:30] ? 01/21/2012 03:00:00 First cycle set for: Sat Jan 21 03:00:00 2012 Enter the number of minutes to delay for the clamp test [1] ? Clamp test delay set for 1 minutes Enter sampling interval in minutes [360] ? 60 Sampling interval is 60 minutes Enter the time out (in seconds) for the up cast [800] ? Time out for up cast is set at 800 seconds Enter minimum depth to trigger the up cast termination [4.000000] ? 8 Minimum depth trigger is set at 8.0 meters Enter the time out (in seconds) for the down cast) [600] ? Time out for down cast is set at 600 seconds Enter maximum depth to trigger the down cast termination [50.000000] ? Maximum depth trigger is set at 50.0 meters Enter the time (in seconds) to wait at the surface for offload attempts [0] ? Time at surface is set at 0 seconds The configuration string is as follows: parameters: 8 first cycle: 01/21/2012 03:00:00 test cycle: 1 cycle interval: 60 ascend timeout: 800 ascend trigger depth: 8.0 descend timeout: 600 descend trigger depth: 50.0 surface time: 0 Do you want to save the configuration to a file? If so, then this file will be used for future deployments [Y] ? Configuration data file written Opening and reading configuration file for confirmation... Configuration file settings: ---------------------------- Number of parameters to read: 8 First cycle set for: Sat Jan 21 03:00:00 2012 Clamp test delay set for: 1 minutes Cycle interval set for: 60 minutes Ascending timeout set for: 800 seconds Ascending trigger depth set for: 8.0 meters Descending timeout set for: 600 seconds Descending trigger depth set for: 50.0 meters Time to wait at surface set for: 0 seconds Press to continue... SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? d SeaHorse Deployment Setup Enter new time (mm/dd/yyyy hh:mm:ss) if time is wrong [01/21/2012 01:18:52] ? 01/21/2012 01:20:00 System clock curently reads: Sat Jan 21 01:20:00 2012 Do you want to test the CTD [Y] ? SBE19plus: Powering Sending STOP\r, 1/30 Timeout on attempt 1 Sending , 2/30 Timeout on attempt 2 Sending , 3/30 SSeacatPlus S> '>' prompt detected (3/30) SBE19plus: Clock-Sync Sending \r, 1/30 S> '>' prompt detected (1/30) Sending MMDDYY=012112\r, 1/30 MMDDYY=012112 S> '>' prompt detected (1/30) Sending HHMMSS=012021, 1/1 Sending \r, 1/1 S> '>' prompt detected (1/1) SBE19plus: Clock-Sync complete. Sending STARTNOW\r, 1/20 STARTNOW S> '>' prompt detected (1/20) CTD ready. Entering instrument ascii direct mode Press ~ to exit 061DFF0A54A607F0674FF9458E0F61 061E010A54A407F06A4FF945940F4E 061E040A54A807F06A4FF945920F59 061E040A54A807F06A4FF945990F59 061E070A54A407F0694FF945920F75 061E0A0A54A807F0694FF945920F62 061E0B0A54A507F0694FFB45980F71 061E0F0A54A407F0674FFA45910F5B 061E110A54A807F0674FFA45910F56 061E170A54A507F0684FFC45880F5A 061E170A54A707F0684FFC458E0F55 061E190A54A507F0694FFA45860F4E 061E1E0A54A807F0674FFC457E0F4F 061E200A54A407F0684FFB45870F4B SBE19plus: Shutdown Sending STOP\r, 1/30 06 1F0A54A507F0664FFD457C0F4A S> '>' prompt detected (1/30) SBE19plus: enter quiescent state Sending QS\r, 1/1 QS Timeout on attempt 1 CTD test complete...continuing with deployment setup. User header: ** Cruise: NBP12-01 ** Station: 1 ** Ship: RVIB Nathaniel B Palmer ** Chief_Scientist: Greenan ** Organization: DFO ** Area_of_Operation: Ross Sea ** Package: SeaHorse/SBE19plus CTD/WetStar/SBE43-DO/Satlantic OCR504i/FRRF ** Mooring_Number: 1 ** Latitude: -76 29.0 ** Longtitude: 171 06.0 ** Sounding: 800 ** Profile_Direction: up ** Notes: Configuration file settings: ---------------------------- Number of parameters to read: 8 First cycle set for: Sat Jan 21 03:00:00 2012 Clamp test delay set for: 1 minutes Cycle interval set for: 60 minutes Ascending timeout set for: 800 seconds Ascending trigger depth set for: 8.0 meters Descending timeout set for: 600 seconds Descending trigger depth set for: 50.0 meters Time to wait at surface set for: 0 seconds OpFile written successfully Waiting for the clamp test Present time........... Sat Jan 21 01:20:29 2012 Clamp test at.......... Sat Jan 21 01:21:29 2012 First profile at....... Sat Jan 21 03:00:00 2012 ----------------------- Sleeping till.......... Sat Jan 21 01:21:29 2012 ----------------------- Present time........... Sat Jan 21 01:21:30 2012 Starting clamp test CLIMB MODE Cam_sw: 1 Current: 0.370 Apk FREE MODE Cam_sw: 0 Current: 0.364 Apk Clamp test complete Present time........... Sat Jan 21 01:21:46 2012 Next profile at........ Sat Jan 21 03:00:00 2012 ----------------------- Sleeping till.......... Sat Jan 21 02:59:00 2012 -----------------------