Nortek Vec: DISABLED EPS Mapper: DISABLED MAVS: DISABLED OCR 504: *ENABLED* IMM: DISABLED Upload Auxilary Files: *ENABLED* OCR504 uart opened Configuration file settings: ---------------------------- Number of parameters to read: 8 First cycle set for: Fri Jan 4 23:00:00 2013 Clamp test delay set for: 1 minutes Cycle interval set for: 360 minutes Ascending timeout set for: 800 seconds Ascending trigger depth set for: 4.0 meters Descending timeout set for: 600 seconds Descending trigger depth set for: 50.0 meters Time to wait at surface set for: 0 seconds Stored calibration settings: ---------------------------- Motor current coefficient: 0.000755 Aux 1 current coefficient: 0.000220 Aux 2 current coefficient: 0.000220 Aux 3 current coefficient: 0.000220 Aux 4 current coefficient: 0.000219 Switched battery voltage coefficient: 0.004305 Switched aux voltage coefficient: 0.004290 Depth coefficient: 0.106744 Motor current offset: -15 Aux 1 current offset: 13 Aux 2 current offset: 32 Aux 3 current offset: 6 Aux 4 current offset: 21 Switched battery voltage offset: -34 Switched aux voltage offset: -1 Depth offset: 808 Directory 'DATA' found. SeaHorse II Ver. 2.091 Next cycle will start 5 seconds from now... Press the '&' key to bypass sampling and enter the main menu... Waiting... SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? q ---------------------------------------------------------------- Persistor CF21M SN 04471 PicoDOS V4.01r1 PBM V4.00 (C) 1998-2005 Persistor Instruments Inc. - www.persistor.com ---------------------------------------------------------------- C:\>? ========= PicoDOS built-in commands (plus .PXE and .BAT Files) ========= APP run flash app [args...] ATTRIB [+ - RASH] [d:][p][name] BACKROM [d:][path] [/SAVPI] BAUD [newrate] [/Q/P/E/O/N/2] BOOT [PICO][PBM][APP] CAPTURE [d:][p]fn [/Dx/B/N/E] CCC Card Change [delay secs] CHDIR [drive:][path] CHKDSK [d:][p][fn] [/F][/I] COPY source dest [/V] DUMP file[start[,end]] DATE [mdy[hms[a|p]]] /IEUMCP] DEL [drv:][pth][name] [/P] DIR [d:][p][fn] [/PWBLV4A:a] ERASE [drv:][pth][name] [/P] FDISK [/Pnn/M/Sdev/@/F/Rnn/Q] FORMAT [drv:][/V[:label]][/Q/E] GO args... | addr /A | /Fn LO [ofs][;Bx[+]] [;G] MOUNT [V:][DEV[-n]][/D/P/N/V/Q] MKDIR [drive:][path] MD display [range] MM modify [address] ML disassemble [range] MR Memory Read MR[.bwl] MW Memory Write MW[.bwl] MON Reset to PBM PATH [[d:]path[;...]] [/P] PBM Reset to PBM PROMPT [text] [/P] PR pin read <1..50> PC pin clear <1..50> PS pin set <1..50> PT pin toggle <1..50> PM pin mirror <1..50> TIME [hh:mm:ss [a|p]] [/M/C] TYPE [drv:][pth][name] REN [d:][p]oldname newname RESET (hard reset) RMDIR [drive:][path] SAVE file[start][end] SD sect.dump[d:][range][/C] SET [var=[str]] [/SLFE?] XS [/X][/C][/Q]file XR [/X][/C][/Q][file] YS [/G][/Q]file[,file...] YR [/G][/Q] VER Firmware versions [/I] C:\>date Clock reads: Saturday, January 14, 2012 07:54:53 pm C:\>time 19:57:00 Clock reads: Saturday, January 14, 2012 07:57:00 pm C:\>time Clock reads: Saturday, January 14, 2012 07:57:51 pm C:\>time Clock reads: Saturday, January 14, 2012 07:58:19 pm C:\>time Clock reads: Saturday, January 14, 2012 07:58:29 pm C:\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\ OCR504.HDR 1,294 10-19-11 1:57p TESTFILE.001 0 01-14-12 7:53p DATA 10-25-11 1:28p CONFIG.TXT 192 01-04-12 11:28p OPFILE.TXT 13 01-10-12 4:19a OCR_3.DAT 5,147 01-04-12 11:25p CAST0003.ENG 2,095 01-04-12 11:25p SH__0003.HEX 10,154 01-04-12 11:25p 7 file(s) 18,895 bytes 1 dir(s) 258,367,488 bytes free C:\>? ========= PicoDOS built-in commands (plus .PXE and .BAT Files) ========= APP run flash app [args...] ATTRIB [+ - RASH] [d:][p][name] BACKROM [d:][path] [/SAVPI] BAUD [newrate] [/Q/P/E/O/N/2] BOOT [PICO][PBM][APP] CAPTURE [d:][p]fn [/Dx/B/N/E] CCC Card Change [delay secs] CHDIR [drive:][path] CHKDSK [d:][p][fn] [/F][/I] COPY source dest [/V] DUMP file[start[,end]] DATE [mdy[hms[a|p]]] /IEUMCP] DEL [drv:][pth][name] [/P] DIR [d:][p][fn] [/PWBLV4A:a] ERASE [drv:][pth][name] [/P] FDISK [/Pnn/M/Sdev/@/F/Rnn/Q] FORMAT [drv:][/V[:label]][/Q/E] GO args... | addr /A | /Fn LO [ofs][;Bx[+]] [;G] MOUNT [V:][DEV[-n]][/D/P/N/V/Q] MKDIR [drive:][path] MD display [range] MM modify [address] ML disassemble [range] MR Memory Read MR[.bwl] MW Memory Write MW[.bwl] MON Reset to PBM PATH [[d:]path[;...]] [/P] PBM Reset to PBM PROMPT [text] [/P] PR pin read <1..50> PC pin clear <1..50> PS pin set <1..50> PT pin toggle <1..50> PM pin mirror <1..50> TIME [hh:mm:ss [a|p]] [/M/C] TYPE [drv:][pth][name] REN [d:][p]oldname newname RESET (hard reset) RMDIR [drive:][path] SAVE file[start][end] SD sect.dump[d:][range][/C] SET [var=[str]] [/SLFE?] XS [/X][/C][/Q]file XR [/X][/C][/Q][file] YS [/G][/Q]file[,file...] YR [/G][/Q] VER Firmware versions [/I] C:\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\ OCR504.HDR 1,294 10-19-11 1:57p TESTFILE.001 0 01-14-12 7:53p DATA 10-25-11 1:28p CONFIG.TXT 192 01-04-12 11:28p OPFILE.TXT 13 01-10-12 4:19a OCR_3.DAT 5,147 01-04-12 11:25p CAST0003.ENG 2,095 01-04-12 11:25p SH__0003.HEX 10,154 01-04-12 11:25p 7 file(s) 18,895 bytes 1 dir(s) 258,367,488 bytes free C:\>del *.dat C:\>del *.eng C:\>del *.hex C:\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\ OCR504.HDR 1,294 10-19-11 1:57p TESTFILE.001 0 01-14-12 7:53p DATA 10-25-11 1:28p CONFIG.TXT 192 01-04-12 11:28p OPFILE.TXT 13 01-10-12 4:19a 4 file(s) 1,499 bytes 1 dir(s) 258,392,064 bytes free C:\>cd data \DATA C:\DATA\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\DATA\ . 10-25-11 1:28p .. 10-25-11 1:28p CAST0001.ENG 1,969 01-04-12 11:19p SH__0001.HEX 10,538 01-04-12 11:19p OCR_1.DAT 5,603 01-04-12 11:19p CAST0002.ENG 2,103 01-04-12 11:24p SH__0002.HEX 10,154 01-04-12 11:24p OCR_2.DAT 5,147 01-04-12 11:24p 6 file(s) 35,514 bytes 2 dir(s) 258,392,064 bytes free C:\DATA\>del *.dat C:\DATA\>del *.eng C:\DATA\>del *.hex C:\DATA\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\DATA\ . 10-25-11 1:28p .. 10-25-11 1:28p 0 file(s) 0 bytes 2 dir(s) 258,441,216 bytes free C:\DATA\>cd .. C:\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\ OCR504.HDR 1,294 10-19-11 1:57p TESTFILE.001 0 01-14-12 7:53p DATA 10-25-11 1:28p CONFIG.TXT 192 01-04-12 11:28p OPFILE.TXT 13 01-10-12 4:19a 4 file(s) 1,499 bytes 1 dir(s) 258,441,216 bytes free C:\>? ========= PicoDOS built-in commands (plus .PXE and .BAT Files) ========= APP run flash app [args...] ATTRIB [+ - RASH] [d:][p][name] BACKROM [d:][path] [/SAVPI] BAUD [newrate] [/Q/P/E/O/N/2] BOOT [PICO][PBM][APP] CAPTURE [d:][p]fn [/Dx/B/N/E] CCC Card Change [delay secs] CHDIR [drive:][path] CHKDSK [d:][p][fn] [/F][/I] COPY source dest [/V] DUMP file[start[,end]] DATE [mdy[hms[a|p]]] /IEUMCP] DEL [drv:][pth][name] [/P] DIR [d:][p][fn] [/PWBLV4A:a] ERASE [drv:][pth][name] [/P] FDISK [/Pnn/M/Sdev/@/F/Rnn/Q] FORMAT [drv:][/V[:label]][/Q/E] GO args... | addr /A | /Fn LO [ofs][;Bx[+]] [;G] MOUNT [V:][DEV[-n]][/D/P/N/V/Q] MKDIR [drive:][path] MD display [range] MM modify [address] ML disassemble [range] MR Memory Read MR[.bwl] MW Memory Write MW[.bwl] MON Reset to PBM PATH [[d:]path[;...]] [/P] PBM Reset to PBM PROMPT [text] [/P] PR pin read <1..50> PC pin clear <1..50> PS pin set <1..50> PT pin toggle <1..50> PM pin mirror <1..50> TIME [hh:mm:ss [a|p]] [/M/C] TYPE [drv:][pth][name] REN [d:][p]oldname newname RESET (hard reset) RMDIR [drive:][path] SAVE file[start][end] SD sect.dump[d:][range][/C] SET [var=[str]] [/SLFE?] XS [/X][/C][/Q]file XR [/X][/C][/Q][file] YS [/G][/Q]file[,file...] YR [/G][/Q] VER Firmware versions [/I] C:\>xr header.txt Receiving ... CCCCCComplete C:\>dir Volume in drive C has no label Volume Serial Number is 7534-7AA6 Directory of C:\ OCR504.HDR 1,294 10-19-11 1:57p TESTFILE.001 0 01-14-12 7:53p DATA 10-25-11 1:28p CONFIG.TXT 192 01-04-12 11:28p OPFILE.TXT 13 01-10-12 4:19a HEADER.TXT 384 01-14-12 8:16p 5 file(s) 1,883 bytes 1 dir(s) 258,437,120 bytes free C:\>type header.txt ** Cruise: NBP12-01 ** Station: 1 ** Ship: RVIB Nathaniel B Palmer ** Chief_Scientist: Greenan ** Organization: DFO ** Area_of_Operation: Ross Sea ** Package: SeaHorse/SBE19plus CTD/WetStar/SBE43-DO/Satlantic OCR504i/FRRF ** Mooring_Number: 1 ** Latitude: -76 29.0 ** Longtitude: 171 06.0 ** Sounding: 800 ** Profile_Number: ** Profile_Direction: up ** Notes:  C:\>del header.txt C:\>yr Receiving ... CCComplete C:\>type header.txt ** Cruise: NBP12-01 ** Station: 1 ** Ship: RVIB Nathaniel B Palmer ** Chief_Scientist: Greenan ** Organization: DFO ** Area_of_Operation: Ross Sea ** Package: SeaHorse/SBE19plus CTD/WetStar/SBE43-DO/Satlantic OCR504i/FRRF ** Mooring_Number: 1 ** Latitude: -76 29.0 ** Longtitude: 171 06.0 ** Sounding: 800 ** Profile_Number: ** Profile_Direction: up ** Notes: C:\>type config.txt parameters: 8 first cycle: 01/04/2013 23:00:00 test cycle: 1 cycle interval: 360 ascend timeout: 800 ascend trigger depth: 4.0 descend timeout: 600 descend trigger depth: 50.0 surface time: 0 C:\>ys config.txt Sending: CONFIG.TXT Complete C:\> Nortek Vec: DISABLED EPS Mapper: DISABLED MAVS: DISABLED OCR 504: *ENABLED* IMM: DISABLED Upload Auxilary Files: *ENABLED* OCR504 uart opened Configuration file settings: ---------------------------- Number of parameters to read: 8 First cycle set for: Fri Jan 4 23:00:00 2013 Clamp test delay set for: 1 minutes Cycle interval set for: 360 minutes Ascending timeout set for: 800 seconds Ascending trigger depth set for: 4.0 meters Descending timeout set for: 600 seconds Descending trigger depth set for: 50.0 meters Time to wait at surface set for: 0 seconds Stored calibration settings: ---------------------------- Motor current coefficient: 0.000755 Aux 1 current coefficient: 0.000220 Aux 2 current coefficient: 0.000220 Aux 3 current coefficient: 0.000220 Aux 4 current coefficient: 0.000219 Switched battery voltage coefficient: 0.004305 Switched aux voltage coefficient: 0.004290 Depth coefficient: 0.106744 Motor current offset: -15 Aux 1 current offset: 13 Aux 2 current offset: 32 Aux 3 current offset: 6 Aux 4 current offset: 21 Switched battery voltage offset: -34 Switched aux voltage offset: -1 Depth offset: 808 Directory 'DATA' found. SeaHorse II Ver. 2.091 Next cycle will start 5 seconds from now... Press the '&' key to bypass sampling and enter the main menu... Waiting... SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? m Instrument Direct Menu: ----------------------- Connect to CTD [C] Connect to OCR504 [O] Quit to main menu [Q] enter selection....... [C] ? c Entering instrument ascii direct mode Press ~ to exit SeacatPlus S>ds SeacatPlus V 1.3a SERIAL NO. 4142 14 Jan 2012 20:30:35 vbatt = 13.3, vlith = 7.8, ioper = 61.4 ma, ipump = 67.0 ma, iext01 = 4.4 ma, iext23 = 37.0 ma, status = not logging number of scans to average = 1 samples = 0, free = 558694, casts = 0 mode = profile, minimum cond freq = 3145, pump delay = 40 sec ignore magnetic switch = yes battery type = ALKALINE, battery cutoff = 7.5 volts pressure sensor = strain gauge, range = 508.0 SBE 38 = no, Gas Tension Device = no Ext Volt 0 = yes, Ext Volt 1 = no, Ext Volt 2 = yes, Ext Volt 3 = no echo commands = yes output format = raw HEX S>initlogging S>ds SeacatPlus V 1.3a SERIAL NO. 4142 14 Jan 2012 20:31:08 vbatt = 13.3, vlith = 7.8, ioper = 61.4 ma, ipump = 78.9 ma, iext01 = 4.4 ma, iext23 = 38.5 ma, status = not logging number of scans to average = 1 samples = 0, free = 558694, casts = 0 mode = profile, minimum cond freq = 3145, pump delay = 40 sec ignore magnetic switch = yes battery type = ALKALINE, battery cutoff = 7.5 volts pressure sensor = strain gauge, range = 508.0 SBE 38 = no, Gas Tension Device = no Ext Volt 0 = yes, Ext Volt 1 = no, Ext Volt 2 = yes, Ext Volt 3 = no echo commands = yes output format = raw HEX S> SBE19plus: Shutdown Sending STOP\r, 1/30 STOP S> '>' prompt detected (1/30) SBE19plus: enter quiescent state Sending QS\r, 1/1 QS Timeout on attempt 1 Instrument Direct Menu: ----------------------- Connect to CTD [C] Connect to OCR504 [O] Quit to main menu [Q] enter selection....... [C] ? q SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? e Displaying system data Type 'q' to quit...any other key to continue Motor curnt(a/d): 106 Current: 0.091(a) Aux 1 curnt(a/d): 194 Current: 0.040(a) Aux 2 curnt(a/d): 26 Current: -0.001(a) Aux 3 curnt(a/d): 115 Current: 0.024(a) Aux 4 curnt(a/d): 182 Current: 0.035(a) Battery(a/d): 3229 Battery: 14.047(v) Aux(a/d): 3238 Aux: 13.895(v) Depth(a/d): 808 Depth: 0.000(m) Selector Status: 0 Motor curnt(a/d): 111 Current: 0.095(a) Aux 1 curnt(a/d): 25 Current: 0.003(a) Aux 2 curnt(a/d): 27 Current: -0.001(a) Aux 3 curnt(a/d): 111 Current: 0.023(a) Aux 4 curnt(a/d): 2471 Current: 0.538(a) Battery(a/d): 3058 Battery: 13.311(v) Aux(a/d): 3067 Aux: 13.162(v) Depth(a/d): 797 Depth: -1.174(m) Selector Status: 0 Motor curnt(a/d): 107 Current: 0.092(a) Aux 1 curnt(a/d): 24 Current: 0.002(a) Aux 2 curnt(a/d): 26 Current: -0.001(a) Aux 3 curnt(a/d): 148 Current: 0.031(a) Aux 4 curnt(a/d): 4095 Current: 0.894(a) Battery(a/d): 3010 Battery: 13.104(v) Aux(a/d): 3016 Aux: 12.943(v) Depth(a/d): 803 Depth: -0.534(m) Selector Status: 0 SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? g Entering user configuration setup Enter time (mm/dd/yyyy hh:mm:ss) of first cycle [01/15/2012 02:17:31] ? 01/15/2012 04:00:00 First cycle set for: Sun Jan 15 04:00:00 2012 Enter the number of minutes to delay for the clamp test [1] ? Clamp test delay set for 1 minutes Enter sampling interval in minutes [360] ? 60 Sampling interval is 60 minutes Enter the time out (in seconds) for the up cast [800] ? Time out for up cast is set at 800 seconds Enter minimum depth to trigger the up cast termination [4.000000] ? 8 Minimum depth trigger is set at 8.0 meters Enter the time out (in seconds) for the down cast) [600] ? Time out for down cast is set at 600 seconds Enter maximum depth to trigger the down cast termination [50.000000] ? Maximum depth trigger is set at 50.0 meters Enter the time (in seconds) to wait at the surface for offload attempts [0] ? Time at surface is set at 0 seconds The configuration string is as follows: parameters: 8 first cycle: 01/15/2012 04:00:00 test cycle: 1 cycle interval: 60 ascend timeout: 800 ascend trigger depth: 8.0 descend timeout: 600 descend trigger depth: 50.0 surface time: 0 Do you want to save the configuration to a file? If so, then this file will be used for future deployments [Y] ? Configuration data file written Opening and reading configuration file for confirmation... Configuration file settings: ---------------------------- Number of parameters to read: 8 First cycle set for: Sun Jan 15 04:00:00 2012 Clamp test delay set for: 1 minutes Cycle interval set for: 60 minutes Ascending timeout set for: 800 seconds Ascending trigger depth set for: 8.0 meters Descending timeout set for: 600 seconds Descending trigger depth set for: 50.0 meters Time to wait at surface set for: 0 seconds Press to continue... SeaHorse II v2.091 [Oct 19 2011 15:33:35] Configured CTD: Seabird SBE 19 Plus (9600_N_8_1) ---------------------------------------------- Format flash card [A] Display directory [B] Create configuration file [G] Create user header [H] Deploy SeaHorse [D] Display system data [E] Select free mode [F] Select climb mode [C] Instrument direct mode [M] Configure CTD [N] Update system calibration [U] View system calibration [V] Seahorse calibration [S] Select Payload Instruments [P] Operational Parameters [O] Test IMM [I] Power FRRf ON [J] Power FRRf OFF [K] Quit [Q] Enter selection........... [ ] ? d SeaHorse Deployment Setup Enter new time (mm/dd/yyyy hh:mm:ss) if time is wrong [01/15/2012 02:17:30] ? System time has not been changed System clock curently reads: Sun Jan 15 02:17:43 2012 Do you want to test the CTD [Y] ? SBE19plus: Powering Sending STOP\r, 1/30 Timeout on attempt 1 Sending , 2/30 Timeout on attempt 2 Sending , 3/30 SSeacatPlus S> '>' prompt detected (3/30) SBE19plus: Clock-Sync Sending \r, 1/30 S> '>' prompt detected (1/30) Sending MMDDYY=011512\r, 1/30 MMDDYY=011512 S> '>' prompt detected (1/30) Sending HHMMSS=021750, 1/1 Sending \r, 1/1 S> '>' prompt detected (1/1) SBE19plus: Clock-Sync complete. Sending STARTNOW\r, 1/20 STARTNOW S> '>' prompt detected (1/20) CTD ready. Entering instrument ascii direct mode Press ~ to exit 068C490A549A07F0BD4E074C6C056D 068C4E0A549D07F0C04E0A4C59056F 068C4E0A549D07F0BE4E0B4C5D0577 068C530A549D07F0BC4E094C630585 068C5B0A549D07F0BE4E094C5E0584 068C600A549A07F0BE4E0B4C5F058B 068C690A549A07F0BD4E0B4C630592 068C660A549A07F0BC4E0B4C620580 068C6C0A549A07F0BC4E0C4C650582 068C710A549D07F0BC4E0B4C66058F 068C770A549D07F0BD4E0B4C670595 068C7B0A549A07F0BB4E0B4C5D058E 068C810A549A07F0BC4E0A4C670584 068C840A549D07F0BC4E0A4C63058C 068C8A0A549D07F0BE4E0A4C6D0584 068C8D0A549A07F0BD4E0A4C6F0593 068C920A549D07F0BD4E0C4C5D057C 068C9A0A549A07F0BD4E0B4C680589 SBE19plus: Shutdown Sending STOP\r, 1/30 S> '>' prompt detected (1/30) SBE19plus: enter quiescent state Sending QS\r, 1/1 QS Timeout on attempt 1 CTD test complete...continuing with deployment setup. User header: ** Cruise: NBP12-01 ** Station: 1 ** Ship: RVIB Nathaniel B Palmer ** Chief_Scientist: Greenan ** Organization: DFO ** Area_of_Operation: Ross Sea ** Package: SeaHorse/SBE19plus CTD/WetStar/SBE43-DO/Satlantic OCR504i/FRRF ** Mooring_Number: 1 ** Latitude: -76 29.0 ** Longtitude: 171 06.0 ** Sounding: 800 ** Profile_Direction: up ** Notes: Configuration file settings: ---------------------------- Number of parameters to read: 8 First cycle set for: Sun Jan 15 04:00:00 2012 Clamp test delay set for: 1 minutes Cycle interval set for: 60 minutes Ascending timeout set for: 800 seconds Ascending trigger depth set for: 8.0 meters Descending timeout set for: 600 seconds Descending trigger depth set for: 50.0 meters Time to wait at surface set for: 0 seconds OpFile written successfully Waiting for the clamp test Present time........... Sun Jan 15 02:17:59 2012 Clamp test at.......... Sun Jan 15 02:18:59 2012 First profile at....... Sun Jan 15 04:00:00 2012 ----------------------- Sleeping till.......... Sun Jan 15 02:18:59 2012 ----------------------- Present time........... Sun Jan 15 02:19:00 2012 Starting clamp test CLIMB MODE Cam_sw: 1 Current: 0.349 Apk FREE MODE Cam_sw: 0 Current: 0.328 Apk Clamp test complete Present time........... Sun Jan 15 02:19:14 2012 Next profile at........ Sun Jan 15 04:00:00 2012 ----------------------- Sleeping till.......... Sun Jan 15 03:59:00 2012 -----------------------