[ ======================================================================= ] [ OS ADCP Test ] [ ************* ] [ ] [ The following tests are basic tests which will confirm that your system ] [ is ready for use. Some tests will need to be run with the system in ] [ water. You will be prompted when this is necessary. ] [ ] [ Connect the OS ADCP to power and the PC as described in the manual. ] [ Turn on power to the OS ADCP. ] [ ] [ The results of all tests will be printed to the screen and saved to the ] [ log file OS_TESTS.TXT. A file called OS_TESTS.TXT with the results of ] [ this test will be created in the same directory as the BBTALK program ] [ is running from. ] [ ] [ The following tests will be performed: ] [ ] [ PT8 RAM Verification Test ] [ PT9 ROM Verification Test ] [ PT3 Interference Verification Test ] [ PT6 Bandwidth Verification Test ] [ ] [ Program is delaying 20 seconds before continuing. ] [ Press to continue. ] > [ ========================================================================] [ ] [ Sending a break to Wake Up the System ] Ocean Surveyor Broadband/Narrowband ADCP RD Instruments (c) 1997-2000 All rights reserved. Firmware Version: 23.08 > [ ======================================================================= ] [ ] [ Restoring factory defaults into temporary memory for TEST. ] [ ] CR1 [Parameters set to FACTORY defaults] > [ ======================================================================= ] [ ] [ Collecting system specific data. ] TS? TS 03/01/22,01:53:47.24 --------- Set System Date and Time >PS0 Frequency: 76800 HZ Configuration: 4 BEAM, JANUS Transducer Type: ROUND 32x32 Beamformer Rev: A02 or later Beam Angle: 30 DEGREES Beam Pattern: CONVEX Orientation: DOWN CPU Firmware: 23.08[3] FPGA Version: XC Attitude Sensor: SYNCHRO > [ ======================================================================= ] [ ] [ Starting the RAM and ROM Tests. ] PT8 >PT9 > [ ] [ Both of the above test should display a PASS condition. You can review ] [ the file OS_RSLTS.TXT to verify results. Consult your Technical ] [ Manual for trouble shooting tips if this test did not pass. ] [ ] [ Program is delaying 10 seconds before continuing. ] [ Press to continue. ] > [ ======================================================================= ] [ ] [ PT3 -- Interference Verification Test ] [ The following tests will verify that the internal electronics are ] [ not be interfered with. These tests are best run when the transducer ] [ face is submerged in water. A bucket of water deep enough to cover ] [ the transducer beams is all that is needed. If done in air these tests ] [ will fail. Be sure that all sonar devices and any other device which ] [ may emit a signal that can interfere with the ADCP is turned off. This ] [ includes some PC monitors. ] [ ] [ Program is delaying 10 seconds before continuing. ] [ Press to continue. ] > [ ======================================================================= ] [ ] [ Sending a break to Wake Up the System ] Ocean Surveyor Broadband/Narrowband ADCP RD Instruments (c) 1997-2000 All rights reserved. Firmware Version: 23.08 > [ ======================================================================= ] [ ] [ Starting the Interference Test.] PT3 Correlation Magnitude: Lag Bm1 Bm2 Bm3 Bm4 0 1.00 1.00 1.00 1.00 1 0.83 0.83 0.82 0.83 2 0.46 0.45 0.44 0.45 3 0.15 0.16 0.16 0.16 4 0.06 0.08 0.12 0.09 5 0.06 0.06 0.11 0.08 6 0.04 0.04 0.07 0.05 7 0.04 0.03 0.06 0.06 RSSI: 33 85 42 33 > [ ] [ Review the file OS_RSLTS.TXT to verify results. Compare the results ] [ from the above test to your Technical Manual. Remember that this test ] [ will fail unless the transducer is immersed in water and if there are ] [ external devices operating at the same time. Consult your Technical ] [ Manual for trouble shooting tips if this test did not pass. ] [ ] [ Program is delaying 10 seconds before continuing. ] [ Press to continue. ] > [ ======================================================================= ] [ ] [ PT6 -- Bandwidth Verification Test ] [ The following tests will verify that the transducer and its receive ] [ circuitry are working properly. These tests are best run when the ] [ transducer face is submerged in water. A bucket of water deep enough ] [ to cover the transducer beams is all that is needed. If done in air ] [ these tests will fail. Be sure that all sonar devices and any other ] [ device which may emit a signal that can interfere with the ADCP is ] [ turned off. This includes some PC monitors. ] [ ] [ Program is delaying 10 seconds before continuing. ] [ Press to continue. ] [ ======================================================================= ] [ ] [ Sending a break to Wake Up the System ] Ocean Surveyor Broadband/Narrowband ADCP RD Instruments (c) 1997-2000 All rights reserved. Firmware Version: 23.08 > [ ======================================================================= ] [ ] [ Starting the Bandwidth Test. ] PT6 Receive Bandwidth: ..........           Expected Bm1 Bm2 Bm3 Bm4 -------- ----- ----- ----- ----- 7680 6870 7108 6617 6827 > [ ] [ Review the file OS_RSLTS.TXT to verify results. Compare the results ] [ from the above test to your Technical Manual. Remember that this test ] [ will fail unless the transducer is immersed in water and if there are ] [ external devices operating at the same time. Consult your Technical ] [ Manual for trouble shooting tips if this test did not pass. ] [ ] [ ======================================================================= ] [ All tests have been run and if passed your system is ready for ] [ deployment. ]